ADEMCO 5130XM Manual de Instruções

ViSI!!IiIAXMSERIES4140XM/51 30XM/4130XMINSTALLATIONINSTRUCTIONSA complete VISTA T=hnioal ReferenceManual that oan unlock the full power ofthe VISTA XM

111. (B) SYSTEM CONFIGURATION (PERIPHERALS)—REMOTE CONSOLES —GENERALBoth the 4130XM and the 5130XM supply up to280mA (200mA for UL certificated instal

— PASSIVE INFRARED MOTION DETECTORS —GENERAL INFORMATIONPOLLING LOOP PIR (4196)Select a mounting site with the following notes inThe 4196 is a quad el

IV. MOUNTING AND POWERING THE SYSTEMNote that field wiring to these controls/consoles must be completed before the controls/consoles can be,-:xmted.:,

— POWERING THE SYSTEM —PRIMARY POWERPowerto the 4140XM Control panel is supplied by aPlug-In DC Power Pack, 1360. which is rated at850 mA @ 18 volts D

AUXILIARY DEVICE CURRENT DRAW WORKSHEETsDEVtCECURRENT# OF UNITS TOTAL CURRENT4137 Console60 mA5137 Console90 mA4146 Keyswitch20 rnA675 Ground Start Mo

V. SYSTEM OPERATION— SECURITY ACCESS CODES —The VISTA XM System allows up to 22 securityThe Installer also programs the master securityaccess codesto

VI.SYSTEM COMMUNICATIONSThe 4171 XT-XM Dialer Board is required for pollingloop and/or wireless zone expansion, and for officeinitiated downloading,an

CONTACT ID REPORTINGThis is the only formal that can identify all 64protection zones by their unique zone (Contact) IDnumbers, and provides a 1digit e

VIII. TESTING THE SYSTEMUSING TEST MODEAfter the installation is completed, the SecuritySystem should be thoroughly tested as follows:1.With the Syste

lx.SPECIFICATIONS4140XM CONTROLPhysical:Width:12 inches (305mm)Height:12 inches (305mm)Depth:3 inches (76mm)Electrical:VOLTAGE INPUT: 18VDC, 85o mA ma

CONGRATULATIONSand WELCOME to the VISTA XM FAMILY!The purpose of these Installation Instructions is to give you, the installer, a brief ovemiewof the

nI@olc-a?~maammMWA?444DomlIID-41@WHuDaw-18-

w❑-“N#i. m\“t----qm/+ –oII 1- 1—II 11(-}: * 1, I-1 se?4’----aw------ ----OJ!3!402:bOOl 3 N) 3A11VNU31VA---------19-/07

. ..--~-H~--. on(--(‘kHHIvE (N.CLOOP]I ZONE1L------------~!llei&–b J!#lLK-I-----d1~1,I-1NRDiBLKla<,----f----!@1)$))))))[,i+II,-20-

“FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT”This equipment has been tested to FCC requirementsand has been foundacceptable for use. The FCC req

L ~,.,mwln——2$-4?7sI1I=%mwr-1I=wm?i?iEl234s67#urnr I Iu?lwlwlwlwlutql=+-anrul~~ ,1.1’1.1,1.IUP/-

WARNINGTHE LIMITATIONS OF THIS ALARM SYSTEMWhite this system is an advanced design security system, it does nol offer guaranteed protection againstbur

ADEMCOLlmlted WarrantyAlarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries andaffiliates fseller), 1

DearValuedCuatomet%Tohelp provideyou withthe best possibieproductsand semice, pieasetake a fewminutesto compietethis surveyand drop it in the maii.We

s3LvJs a311Nn3H.1NlagmvbvdIAMVSS323N39VlSOd ON33SS3Wl~V AQ CllVd 3S llIM 39VlSOdL6L11AN ‘J3SSOAS● S81“ONllMH3d SSVW lSldId0klV3 Ald3M SS3NIW19IIPLEASE

TABLE OF CONTENTS1. GENERAL lNFORMATION ...4Il.ZONE TYPE DEFINITIONS ...

1.GENERALTHE VISTA CONTROLSThe VISTA XM Controls are microprocessor baaedprogrammable systems and feature EEROM memorytechnology (power loss doea not

Il. ZONE TYPE DEFINITIONSEach zone must be assigned to a zone type, which defines the way in which the system responds to faults in thatzone. In addit

Ill. (A) SYSTEM CONFIGURATION (ZONES)—BASIC 9 HARD-WIRED ZONES —ZONE 1 ZONES 2 THROUGH 8Thii zone has a 350 miltiind response and can beThese zones ha

— 2-WIRE POLLING(Zones 10GENERAL INFORMATIONTo expand the system using a 2-wire polling loopand remote point modules (RPMs), a 4171XT-XMdialer board,