ADEMCO Vista-128B PLUS Guia de Configuração descarregar pdf (Página 61)

— 61 —

A = DEVICE ACTION 0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and off; 4 =

Toggle alternately between START and STOP events

EV = EVENT 0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble; 4 = Restore

ZL = ZONE LIST 01-15, 00 = Not Used

"START" ZONE LIST: Upon alarm, fault, trouble or restore of ANY zone in this list, device

action will START.

"STOP" ZONE LIST: Upon restore of ALL zones on this list, device action will STOP. It

need not be same list as used for START.

ZT = ZONE TYPE/SYSTEM OPERATION

Choices for Zone Types are:

00=zone not used 07=24-hour audible 21=arm away

01=entry/exit 1 08=24-hour auxiliary 22=disarm

02=entry/exit 2 09=supervised fire 23=no alarm response

03=perimeter 10=interior (delay) 26=VGM supervision

04=interior (follower) 14=PLM supervision 27=access control

05=day/night burglary 16=fire w/verification 28=MLB supervision

06=24 hour silent 20=arm stay 29=momentary exit

NOTE: Any zone in "ZT" for Start, going into alarm, fault, or trouble will activate the relay.

Any zone in "ZT" for Stop, that restores will stop the relay action.

Choices for System Operation are:

00 = No Response (Not Used) 42 = System Battery Low

01 = Entry/Exit #1 43 = Communication failure

02 = Entry/exit #2 44 = RF Low Battery

03 = Perimeter

27 = Access Point (allows more than

one relay to be controlled by

activation if access point

request)

45 = Polling Loop Failure

04 = Interior Follower 28 = MLB Supervision 47 = Console Failure

05 = Trouble Day/Alarm Night 29 = Momentary Exit 51 = RF Receiver Failure

06 = 24-Hr. Silent 31 = End of Exit Time 52 = Kissoff

07 = 24-Hr. Audible 32 = Start of Entry Time 54 = Fire Zone Reset

08 = 24-Hr. Auxiliary 33 = Any Burglary Alarm 55 = Disarm + 1 Minute

09 = Fire Alarm or Trouble 34 = Code + [#] + 71 Key Entry

10 = Interior W/Delay 35 = Code + [#] + 72 Key Entry

56 = XX Minutes (enter XX in field

1*74) *

16 = Fire With Verification 36 = At Bell Timeout **

20 = Arming-STAY*** 37 = 2 Times Bell Timeout **

57 = YY Seconds (enter YY in field

1*75) *

21 = Arming-AWAY**** 38 = Chime 58 = Duress

22 = Disarming (Code + Off) 39 = Fire Alarm

23 = No Alarm Response 40 = Bypassing

41 = AC Power Fail

60 = Audio Alarm Verification (must

be selected for both START and

STOP operation)

* Stop condition only

** Or at Disarming, whichever occurs earlier

*** The output also activates when the partition is armed in the INSTANT mode

**** The output also activates when the partition is armed in the MAXIMUM mode

P = PARTITION No. 1-8, 0 = Any

ZONE LISTS FOR OUTPUT DEVICES – Programmed in the #93 Menu Mode in the Output Programming Section. Fill in the

required data on the worksheet below and follow the procedure shown earlier in this

Programming Guide

as you enter the

data during the displays and prompts that appear in sequence. Up to 15 zone lists may be created

Note:

Record desired zone numbers below. More or fewer boxes than shown may be needed, as any list may include

any

all

of system's zone numbers.

Zone List 1: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 2: Started or stopped by zone numbers (enter 000 to end entries).

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 71 72

Comentários a estes Manuais

Sem comentários

ADEMCO Vista-128B PLUS Guia de Configuração Página 61

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO Vista-128B PLUS