.
CWtlOlPROYDObQfOUp8
conlml PROM Data Group 11
To program, set Rotary switch to Posftion 10 (“Restore”) and raise
switches for checked boxes.
To program. set Rotary Switch to Position 13 (“Not Used”) and raise
Switches for checked boxes.
Can&al ScIuon Restofs RepoNs: (check as many as desired)
haI Rntora tar Sounding of Mulllplo Alamu In an Armed Period
SWITCHES
j
5 6
7
6
ZONE
ZONE ZONE 4
NOT
5
6
TROUBLE
USED
SWITCHES
1
2
3
4 -
I I
.
ZONE ZONE
ZONE
ZONE
1
2
3
4
5
6 7
6
ZONE ZONE
NOT NOT
5
6 USED I
USED
I
I
I
1
I
NO= This selection is only relevant if Local Restore for Multiple Alarm
Sounding has been selected (see PROM Data Group 11)
Control PROM Data Group S
To program. set Rotary Switch to Position 11 (“Not Used”) and raise
switches for checked boxes.
PwIUI Forood Anning Shunt
SWITCHES
1
2 3
4
Control PROM Datr Group 12
To program, set Rotary Switch to Position 14 (“Not Used”) and raise
switches for checked boxes.
Dolay Extrrlor Alarm Soundlnp and Con&al Statlon Reporting for
Pwlod Delilwd Prevlou8ly
SWITCHES
1
2
3 4
+
ZONE
ZONE ZONE
ZONE ZONE
ZONE 4
ZONE ZONE
1
IF
2 3
4 1
2 3
(ONLY
BURG ZONE)
NOl’Ez User-permissible shuntiig of zones that are to be used as 24
hour zones (i.e. Fire or Emergency/Panic) should NOT be
PROM enabted during programming ff the central monitoring
Statii has already standardized on reporting of Fire as Code 1
and Emergency/Panic as Code 2 (using tow speed or high
speed reporting). This will ensure proper communicator report-
ing of shunts.
ff the above described standardization does sol exist and
Zone 4 (if used for fire) and zone 5 (or 6 if used for
emergency/panic) can be reporled as Codes 4 and 5 respec-
tively, this warning doas not apply).
Control PROM Data Group 10
To program, set Rotary Switch to Position 12 (“Not Used.“) and raise
switches for checked boxes.
Pwmlt ledlvldual Keypad Shun1
SWITCHES
1
2 3
4
ZONE ZONE
ZONE
ZONE
1
2 3
4
i
5
6 7
6
ZONE
ZONE
NOT
NOT
5
6 USED
USED
NOTE: See NOTE under PROM Data Group 9.
8. COMMUNlCATlON PROM
Communication PROM Data Group 1
To program, set Phone No. Setector Switch to “Primary” and Rotary
Switch to Position 1 (Access #) on No. 690 PROM Programmer
Primary PABX Aooass Number (Select from O-9. Up to 4 digits):
q unu
Communkalion PROM Data Group 2
(e.g.. 9)
To program, set Phone No. Selector Switch to “Secondary” and Raary
Switch to Position 1 (Access U) on No. 696 PROM Programmer.
Sacondary PABX Acoau Numb (Select from O-9. Up to 4 digits):
q uun
Communlcatlon PROM Data Group 3
To program, set Phone No. Selector Switch to “Primary” and Rotary
Switch to Position 2 (Main Phone No.) on No. 690 PROM Programmer.
Mmary Teloo Number (Select from O-9. Up to 12 digits):
q uunuuununun
(eg: Out of Area Access digit (1). Area Code. Exchange, Lme Number]
Communlwllon PROM Dota Group 4
To program, set Phone No. Selector Switch to “Secondary” and Rotary
Switch to positiin 2 (Main Phone No.) on No. 690 PROM Programmer.
Secondary Telco Number’ (Select from O-9. up to 12 digits):
q nunnnunuuon
*NOTES: 1. Trailing blanks are pem%siWe for entries less than the
maximum number of digits but leadtng or intermediate
” r-l
blanks are NOT altowed.
..I
2. In certain Telco networks (G.T.B E.). it may be necessary to
program an 11 In the positton Immediately followmg the last
digil of the Telco number. See Note on Page 6 for details.
’
lo
(16 páginas)
(64 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais