.
Cornmunkallon PROM Data
Group 5
CommunkaUon PROM Data Group 6
To program, set Phone No. Selector Switch to “Primary” and Rotary
Switch to Position 3 (Subs lD#) on No. 690 PROM Programmer.
To program, set Phone No. Selector Switch to “Secondary” and Rotary
Switch to Position 3 (Subs ID#) on No. 690 Programmer.
Primary Subscrlbw ID” (Select from O-9):
q uuo
Soowdary Subsorlbw ID” (Select irom O-9):
u u-u q
**NOTfEz All 4 digits must be tilled in. The leading digit is not transmttted
for Ademco Low Speed, SESCOA. and Radionics. Unless a four
digit low speed subscriber I.D. is selected, only the last 3 digits
are transmitted.
Communkatlon PROM Data Group 7
TO program, set Rotary Switch to Position 4 (“No1 Used’) and raise
Adamco Low SpadlSESCOURadlonks Reporllng Codes for
switches for checked boxes represenling bits set within the hexadecimal froubte and Trouble Restore (Select trom O-9. B- F)
code.
“Trouble
“Troubfe Restore
SWITCHES
1
2
3
4
5 6 7
8
I
I
I I
I
I
I
Bit Weights 1
2
4 8
1
2
4
8
(eg: 7 = I + 2 + 4, B = 1 + 2 + 8, C = 4
l
8.0 = 1 + 4 + 8. see page 14)
Communication PROM Data Group 8
To program, set Rotary Switch to Position 5 (“Sys Options*‘) and raise
switches for checked boxes representing bfts set within the hexadecimal
code.
Munco Low SpndlSESCONRadlonl Ro~ortlng Co&s lor
Opwlng and Closkn~ (Select from O-9. B-F)
“Opening’
“Closing’
SWITCHES
1
2
3
4
5 6
7
8
I
I I I
I
I I
I
Bit Weights 1
2
4
8
1
2
4
8
NOTEES: -1. When a Canoat Code has been enabled (PROM Data
here in PROM Data Group 7 and 8 if English language printout is required
‘=Y
Group 4. bit fl5 of the Control PROM) an Opanlng Code
at the Ademco 685 or Radionics 6000/6500 Receivers for the Ademco
must also be enabled hen in PROM Data Group 8.
LOW Speed. Radionics, Radionics “Superfast” and Radionics “BFSK”
“2. The code assignments shown on page 8 are required
formats.
Communiutlon PROM Data Group 6
To program, set Rotary Switch to Position 6 (“Inverted”) and raise
switches for checked boxes representing bits set within the hex-
adecimal code.
Maximum Numbor 01 Attempts lo Old (Select from l-1 5. defaults to 8 if
not programmed)
1
Number of Attempts (l-1 5)
2
3
SWITCHES
4
5 6
7
8
Bit Weights 1
2
4 8
- NOT USED’
‘NOTE: Switches 5-8 must be in down position.
(16 páginas)
(64 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais