ADEMCO 4120XM Guia do Utilizador descarregar pdf (Página 65)

Remote Consoles

Console Is Inoperable; “

Erratic Display

●

Power down completely (AC + battety), disconnect the battery, and power up

again (AC only).

Check that auxiliary voltage is between 12.5VDC-14.0VDC. If not, disconnect all

auxiliary

devices, and take another reading. If now within the above range, there

was too much current being drawn by the auxiliary devices. (see the Auxiliary

Device Worksheet for the current draw of each device). If still not within the

above range, check incoming power from the No. 1361 transformer. Voltage

should be 16.5VAC. If below 15VAC, carefully check the AC supply for a

minimum of 110 VAC.

With all auxiliary devices and batterv still disconnected, check the voltaae on the

red & black

bafiery leads. It should be 13.65VDC (approx.). If not, re~lace the

Control. If it is @ 13.65VDC, the battery may not be at full charge (allow the

battery to charge 12-24 hours before reconnecting the auxiliary devices) or the

battery may be bad, and not able to hold a charge.

Hard-Wired Zones, 1-8

Zone 1 in trouble

● If zone 1 is programmed for fire (response type 9), make sure that field 1●46 is

(“CHECK” or “FAULT”)

set to “3” (zone 1 EOLR). Also,make

sure that the RED jumper is intact and that

there is a 2,000 ohm EOLR across the last device, as described in the SYSTEM

CONFIGURATION: ZONES section. All devices must be normally open and

connected in parallel across terminals 9 and 10.

● If zone 1 is programmed as a non-fire response type and field ●41 is

programmed as a “O”(EOLR required), make sure that the RED jumper is intact

and that there is a 2000 ohm EOLR connected across the last device, as

described in the SYSTEM CONFIGURATION: ZONES section.All devices must

be normally open and connected in parallel across terminals 9 and 10. Check

that field 1

●46 is set to “3” (zone 1 EOLR).

c If zone 1 is programmed as a non-fire response type and field *41 is

programmed as a”1” (normall closed loops), make sure that the

RED jumper is

cut, and that normally closed devices are connected

in series between terminals

10 and 12 as described n the SYSTEM CONFIGURATION: ZONES section.

Zones 2-8 not detecting ● If using EOLRS,check that program field *41=0; if not using EOLRS, ●41=1.

faults when their EOLRS

are shorted (READY

display stays on)

Zones 1-8 is not detecting

“

Check program fields 1•18 and 1•19 to make sure the wired zone(s) in question

faults (READY light stays

have

not been enabled as RF zones.

on)

Hard-Wired Zones On 4219 Wired Zone Expander

Zones on 4219 not

●

detecting faults

●

“81” appears in the ●

console dispiay and rapid .

beeping occurs.

●

Make sure that RF zones do not overlap any of the 4219 zones.

Make sure that Address 1*58 is programmed correctly and that the correct

response types have been entered for the corresponding zones.

Make sure that the dipswitches on the 4219 are set in accordance with Figure 1

in the section titled WIRED ZONE EXPANSION.

The 4219 wired zone expander is not responding to the control panel.

Check that the control is wired properly to the 4219.

Check that the wire run length is in agreement with the recommended wire

gauge.

Make sure that the dipswitches on the 4219 are set in accordance with Figure 1

in the section titled WIRED ZONE EXPANSION.

-65-

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 ... 79 80

Comentários a estes Manuais

Sem comentários

ADEMCO 4120XM Guia do Utilizador Página 65

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO 4120XM