ADEMCO 4140XMPT2 Manual do Utilizador descarregar pdf (Página 19)

Transmitters

NOTE: After replacing a bw

or dead battery, activate the

transmitter and enter the

security code + OFF to clear

its memory of the “Low

Battery” signal.

I w I Wllww II w

LauIw WJI I u Ilal Kwu wvuUIUW u m m IIILK71 u IaIaULWI I=L*O.

‘transmitters(Generel)

● Supports 5700 or 5800 series transmitters.

● Each transmitter has its own unique transmitter ID

number (Zone #). 5700 series transmitters use DIP

switches to set the ID. 5800 series transmitters must

have their ID nurrbers “learned” by the system.

● 5700 series transmitters and the 5827 keypad must also

be set for a house ID. Other 5800 series transmitters

have built-in serial numbers and do not require a house

ID to be set. After installation, check that all transmitters

have been assigned the proper house ID by using the

procedure described later.

‘rans. SupervWlon

● Each transmitter (except 5701, 5727, 5802, 5802CP &

5803) is supervised by a check-in signal that is sent to

the receiver at 70-90 minute intervals. If at least one

Check-in is not received from a transmitter within a

programmed interval (field 1*31), the console will display

the transmitter number and “CHECK” will be displayed.

● Each transmitter (including 5701; 5727, 5802, 5802CP

&5803) is also supervised for low battery conditions, and

will transmit a low battery signal to the receiver when the

battery has approximately 30 days of life remaining. The

console will display the transmitter number and “LO

BAT”.

;800 Series “Learn”

● 5800 series transmitters have built-in serial numbers that

must be “learned” by the system during programming.

Referto the PROGRAMMING GUIDE for details.

:hecking Trans.

● To check that all transmitters have been set property,

>peration including

set the receiver to the proper house ID

)IP & serial number

and enter the Installer code + [#]+ [3].

Code + [#]+ [3])

● All transmitters that have been enabled for the partition in

which the test was initiated will be displayed. As each

transmitter checks in (up to 2 hours), its ID number will

disappear. A faster way to do this is to fault each

transmitter, which causes a transmission to be sent to the

receiver. When all transmitters have checked in, there

should be no ID numbers displayed.

● NOTE: Repeat this procedure for each parlition that uses

RF transmitters.

‘Go/No Go” Test

● This mode helps determine the best location for each

ulode (Patented) transmitter and is activated by putting the control panel in

the TEST mode (4280 requires removing the its cover).

c The receiver’s sensitivity is reduced by half. Once

transmitters are placed in their desired locations and the

approximate length of wire to be run to sensors is

connected to the transmitter’s screw terminals, open

circuit each transmitter. Do not conduct this test with youf

hand wrapped around the transmitter.

● If a single receiver is used, the console will beep three

times to indicate signal reception. If two receivers are

used, the console will beep once if the first receiver

received the signal, twice if the second receiver received

the sgnal and three times if both receivers heard the

signal (which is desirable for redundant configurations).

● If the console does not beep, reorient or move the

transmitter to another location. Usually a few inches in

either direction is all that is required.

● To exit this mode, enter the installer code and press

OFF (replace the 4280s cover). Note that the Receiver’s

sensitivity is fully restored when this mode is exited.

-19-

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 67 68

Comentários a estes Manuais

Sem comentários

ADEMCO 4140XMPT2 Manual do Utilizador Página 19

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO 4140XMPT2