ADEMCO 4140XMPT2 Manual do Utilizador descarregar pdf (Página 51)

Contact ID Reporting

This is the only format that can identifyall 87 protectionzones by their unique

zone (Contact) ID numbers, and providesa 1-digit event qualifier and 3-digit,

specifically defined event code which quickly identifies the condition being

reported.

Contact ID repofis in DTMF (Dual Tone Multi-Frequency@ 10 charactersper

second)and respondsto a 1400 Hz followedby 2300 Hz handshake,and a 1400

Hz kissoff.Thisformatalsouseschecksuminsteadof two messageverification.A

complete reporttakes under3 seconds.

ContactID Reportingtakestheformat: CCCC Q EEE GG 222 where:

Cccc =

Customer (subscriber) number.

Event qualifier, where: E=new event(1) and R= restore (3)

EEE =

Event code (3 hexadecimal digits), defined in the table on the

next page.

Partition number.

s= Zone/contact ID number

reporting the alarm (001-099), or user

number (001-099) for openklose reports. System status messages

(AC Loss, Walk Test, etc.) contain zeroes in the 222 location.

TABLE OF CONTACT ID EVENT CODES

Code Definition

110 FireAlarm

401 O/C ByUser

121 Duress

403 Power-UpArmed

Inn e:laA n--:.. 7 AnR P.amalh I -

1L& am N rcu uu

123

Audible Panic

131

Perimeter RI1“-I=R’

132 Interior Bb,

133 24 Hour BLIi

134 Entry/Exit

135

-.,f~l:-b.$

150 2,

301 A~

LUSS

302 Low System B

305 System Reset

306 ProgramTamp

309 B-+*-’ ‘A* ‘r

332

Pull l-vu

333 R~ m-!

I vglary

I‘rglary

lurglaty

~dyll~lylu durglary

!4Hour Auxiliary

- I ---

Iatterv

)aucl y I ==1 I ail

‘-” ‘ ‘-p Short-Trouble

r m~~iver Failure-Trouble

“-- ‘ ‘m Trouble

I 004 I nr II

Qlfihd\

c’

‘-wvisic

m -

1c’ ‘nerviSiOn

~a!lper

I ~i M I der Low Batterv

7“”

, “-.-w,”, user

407 ] Remote Arm/Disarm (Download)

452 I late open/close

453 I Fail to open

[Ulun nl 1 I 1

‘switch O/C

I back Requested

STAV

it Mode

. . . .... ..

te Reset

31 I Exception schedule change

32 IAccess schedule chanae

ADVISORY: Ademco’s new Contact ID reporting is capable of uniquely reporting all 87 zones of information, as

well as openings and closings for all 128 users, to central stations equipped with the Ademco 685 receiver using

software level 4.4 or higher. Must be level 4.6 to fully support all new 4140XMPT2 report codes. 685 software

levels below 4.4 cannot support Contact ID reporting. For information regarding updating the 685 receiver,

contact the Technical Support group at 1-800-645-7492 (NY) or 1-800-458-9469 (CA)

-51-

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 67 68

Comentários a estes Manuais

Sem comentários

ADEMCO 4140XMPT2 Manual do Utilizador Página 51

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO 4140XMPT2