ADEMCO 4140XMPT2 Manual do Utilizador descarregar pdf (Página 40)

To ADD a Maater,

Manager or Operator

code

Installer must program at

least one Mastsr cods.

Or Master or Manager code,

but must be code with higher

level of authority than the code

being changed. (i.e. Master

code can add a Manager or

Operator level code, but

cannot add another Master

code;

a Manager code can add

an Operator level code, but

cannot add a Master or another

Manager code).

Once there, the current display becomes attached to that partition and status

requests, etc. are now displayed for that partition,

unless a period of 120 seconds

elapses with no key entries.

To return to your original partition, you may enter the

same key sequence and

end if with your normal partition number or “O”. You’re

now back to where you started. It’s that simple! You may view this operation as a ~

big selector switch and you are at the switch at the console.

EXAMPLE: User may be regularly assigned to partition 1. This would be the

default display for this user, however he may “select” to go to partition 2 for

example.

(Assumes he has been programmed for access to partition 2) The user

enters his normal access code and the proper sequence to select another

partition followed by the number 2 for partition 2. The display will now select

partition 2 information for view and further action. In the above example notice

that no access is allowed for this user into partitions 3-8. Attempts to access

these partitions would be denied automatically.

Important!: Duringuser code entry, normal key depressions at other consoles

in a partition will be ignored. However, panic key depression will cause an alarm

and terminate user entry.

Enter Installer Code- + [8]+ new User # (00-99) + new Usets code

Console will prompt for the Authority Level for this user.

EEKl

Emcl

Access Group?

Enter O-8

Enter the level number as follows:

Master (Arm, Disarm, Bypass, add or modify lower

level users)

2 = Manager (Arm, Disarm, Bypass, add or modify lower

level users)

Operator Level A (Arm, Disarm, Bypass)

4= Operator Level B ( Arm, Disarm)

5 = Operator Level C ( Arm, Disarm only if system armed

with this code)

6 = Duress (Arm, Disarm, triggers silent panic alarm)

Console will then prompt for Open/Close reporting option

for this user.

Press O(NO) or 1 (YES), depending on whether or

not arming/disarming by this user will trigger opening

& closing reports.

If access schedules have been programmed, this

prompt appears. Enter the user’s access group

number (1-8) if this user should have limited access

to the system. Enter Oif no access group should be

assigned.

If a 5800 series button transmitter has been enabled,

and not assgned to a user, this prompt will appear.

If yes

was given as the answer to the RF button

question, the zone number for the button will be

requested. Enter one of the zone numbers

assigned to the button transmitter as AWAY, STAY

or DISARM. The system will then assign any STAY,

AWAY or DISARM buttons of the transmitter to this

user number..

Press O(NO) or 1 (YES). If NO, the program exits this

mode. If yes, the Console prompts for the Global Arm

option for this user.

Press O (NO) or 1 (YES), depending on whether or

not this user will be allowed to arm more than one

partition via Global Arm prompts (described in the

KEYPAD FUNCTIONS section) .

If the Multi-Access option was selected for this user,

the console now prompts for the user’s access to

the next partition.

-40-

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 67 68

Comentários a estes Manuais

Sem comentários

ADEMCO 4140XMPT2 Manual do Utilizador Página 40

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO 4140XMPT2