ADEMCO VISTA-20HWse Guia de Resolução de Problemas descarregar pdf (Página 54)

–54–

02 Start: Part

Any Partition A

Enter (if applicable) the partition number 1 or 2 (or 0 for any).

Press the [

] key to continue.

02 Stop: Zn List

No List 0

If a zone list will be used to STOP, or restore, the device action, enter the zone

list number 1, 2, or 3 (to be programmed in

81 mode). If not used, enter 0.

Press the [

] key to continue.

02 Stop: Zn Typ

Not Used 00

If a zone type or system operation will be used to STOP the device action, enter

the appropriate two digit code (see the "ZT" choices listed above). If not, enter 00.

Press the [

] key to continue.

02 Stop: Part

Any Partition A

Enter (if applicable) the partition number 1 or 2 (or 0 for any). Press the [

] key to

continue.

02 A EV ZL ZT P

STT 0 0 0 00 1

This screen again displays a summary of the current device START programming

. Press the [

] key to continue.

02 A EV ZL ZT P

STP – – 0 00 A

This screen again displays a summary of the current device STOP programming.

Press the [

] key to continue.

02 X10 Device ?

0 = No, 1 = Yes 00

Enter 1 if using a Powerline Carrier Device (X-10); if not, enter 0.

The display then returns again to the first screen so that the next device number

to be programmed can be entered, or enter [0][0] to end device programming.

Example of

Output Device

Programming

A lamp is to be turned on via a Powerline Carrier device (X-10) when any one of 3

specific zones are faulted, or when any 24-hour auxiliary zone is faulted. We want

to be able to turn off the lamp manually without affecting the arming status of the

system.

To program this, we would do the following:

• In

80 interactive mode we choose Output Device 01 and program the Action

(A) to be "2" (Close and stay closed). The Event we are looking for to

start

the

Device action is a fault, so we will program "2" in (EV). We will use Zone List 1

for the 3 specific zones, so we will program "1" in (ZL), (and we will program

these 3 zones in

81's Zone List 1).

• The second condition for turning on the indicator is triggering a 24-hour aux.

zone (Zone Type 08), so we will program (ZT) as "08".

• Next, enter the Partition number (P) in which you want the triggering of a 24-

hour zone to occur; enter 1 or 2, or enter 0 for

any

partition.

• To stop the Device action and turn off the lamp, we do not want to use a restore

of any zone, so a "0" will be programmed for the Restore of Zone List (ZL). We

will use a manual entry of User Code + [#] + [8] + Device # to turn off.

Therefore, we do not need to program a STOP event.

Press [

to continue.

• The system will display a summary screen for the START programming for

device 01. Press [

to continue.

• The system will display a summary screen for the STOP programming for device

01. Press [

to continue.

• The system will display the "X10?" prompt. Enter 1 for yes.

• The Enter Device No. prompt for the next zone will be displayed.

• Press 00 and then [

] to exit the

80 mode.

Now use

81 Zone List mode to program the 3 specific zones in Zone List 1.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 83 84

Comentários a estes Manuais

Sem comentários

ADEMCO VISTA-20HWse Guia de Resolução de Problemas Página 54

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO VISTA-20HWse