ADEMCO 4140XMPT2 Manual do Utilizador descarregar pdf (Página 114)

– 114 –

Section 2. EVENT LOGGING (Connector J8)

Event Logging Printer

Connections

UL NOTE: A UL Listed EDP

printer must be used for UL

installations.

Connector J8, located above connector J7 on the right side of the main PC board,

is intended to be interfaced to a local serial printer via the 4100SM serial interface

module, in applications where it is desired to print the event log on a local printer.

Mount the 4100SM using its clip bracket to attach it to the side wall of the control

cabinet. Make connections between J8, the 4100SM module and the serial printer

as shown below. Refer to the event logging commands paragraph for a

description of the console commands which initiate event log printing.

NOTE 1: Printer must be configured as follows:

• 8 data bits, no parity, 1 stop bit

• 300 or 1200 baud (1200 preferred)

• Hardware handshaking using DTR signal

NOTE 2: The 4100SM module is supplied with a 10 foot RS232 cable. A longer

cable or an extension cable can be used if the 4140XMPT2 and serial printer are

separated by more than 10 feet, but the total cable length should be less than 50'.

NOTE 3: Most printers either ignore the CTS, DSR and CD signals, or require them

to be high (i.e. 3-15VDC as measured on RS232 DB25 connector pins 5, 6 & 8

respectively with respect to ground pin 7). The 4100SM module sets these pins

high. If the printer being used will not operate with these pins high, then clip the

blue (CTS), white (DSR) or red (CD) jumpers on the 4100SM module to set the

corresponding signal floating. Important pins on the RS232C cable are pin 3 (data

out), pin 7 (ground) and pin 20 (DTR - ready).

NOTE 4: The DTR signal, as measured at 4100SM TB1, should be high (9.5-

14VDC) when the printer is powered, properly connected, on-line and ready to

print. This signal will be low (0-1.5VDC) when the printer is not powered, not

properly connected, off-line or out of paper. The 4140XMPT2 will not send

printing data to the printer unless the DTR signal is high.

123456789

J8 CONNECTOR

VIOLET

GRAY

YELLOW

RED

GREEN

BROWN

BLUE

BLACK

IN 2

GROUND

IN 3

GROUND

OUT 5

OUT 6

GROUND

PRINTER DTR

4142TR CABLE (SUPPLIED WITH 4100SM)

4100SM SERIAL MODULE

+ PWR

- (GND)

RXD

not used

DTR

RED BLUE WHITE

To TB6 Aux. Power (+)

(25mA current draw)

To TB7 Aux. Power (-)

Cable

Supplied with

4100SM

USE GENDER CHANGER

SUPPLIED WITH 4100SM

IF PRINTER HAS DB25

MALE CONNECTOR

SERIAL PRINTER

SET FOR: 8 DATA BITS

NO PARITY 1

STOP BIT

300/1200 BAUD

HARDWARE HANDSHAKE

USING DTR SIGNAL

4100SM JUMPERS

(CUT TO SET RESPECTIVE SIGNAL FLOATING)

COLOR FUNCTION PIN#

RED CD 8

BLUE CTS 5

WHITE DSR 6

1 2 ... 109 110 111 112 113 114 115 116 117 118 119 ... 131 132

Comentários a estes Manuais

Sem comentários

ADEMCO 4140XMPT2 Manual do Utilizador Página 114

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO 4140XMPT2