ADEMCO 4140XMPT2 Manual do Utilizador descarregar pdf (Página 57)

– 57 –

Dialer Options

(continued)

*42 Dial Tone Pause

This field sets the delay time for the Dial Tone Detect option, if true dial tone

is not selected in that field. Enter the desired wait time for dial tone

detection as follows: Enter single digit, 0 = 5 seconds; 1 = 11 seconds; or

2 = 30 seconds. Must be 0 for UL.

*43 Dial Tone Detection

Determines whether the control will wait for a true dial tone before dialing, or

if it will wait for a predetermined delay before dialing (delay is programmed in

Dial Tone Pause field *42). The latter may be necessary in high-noise

environment Telco networks where noise can be confused with dial tone,

resulting in premature dialing. Enter 1 for true dial tone wait. If no dial tone is

detected, will dial at end of pause programmed in field *42. Enter 0 to

pause for seconds entered in field *42, then dial.

*44 Ring Detection Count

Only applicable if central station initiated downloading will be used. Enter

00 to disable ring detection. Enter 01-14 for ring counts of 1-14. Enter

15 to select answering machine mode that allows the system to receive

calls even when a telephone answering machines is connected to the

same phone line. In the answering machine mode, the download caller

should let the phone ring once, then hang up, then call again within 30

seconds. The system, upon hearing one ring followed by nothing, will not

answer that call, but will ready itself to pick up on the first ring the next

incoming call that is received within 30 seconds (the downloader calling

again).

*45 Primary Format

This field selects the reporting format for use on the primary telephone line.

Enter the appropriate number for the primary format as follows: 0=Low Speed;

1=Contact ID; 2=Ademco High Speed; 3=Ademco Express

*46 Low Speed Format (Primary)

Enter the appropriate value: 0=Ademco Low Speed; 1=Sescoa/Radionics

*47 Secondary Format

This field selects the reporting format for the secondary telephone line. Enter

the appropriate number for the secondary format as follows: 0=Low Speed;

1=Contact ID; 2=Ademco High Speed; 3=Ademco Express

*48 Low Speed Format (Sec.)

Enter the appropriate value: 0=Ademco Low Speed; 1=Sescoa/Radionics

*49 Checksum Verification

Enter 1 for either or both primary/secondary formats to send a verification

digit to validate the message at the receiver without having to send two

message rounds. Selection is valid for 3+1, 4+2, and Ademco High Speed

reports. Enter 0 if not desired.

*50 Sescoa/Radionics Select

Enter 0 if Radionics format is to be used with hexadecimal 0-9, B-F

reporting. Enter 1 if SESCOA format is to be used with only numeric

reporting (0-9). Note that selection applies to both primary and secondary

phone numbers.

*51 Dual Reporting

This field allows all reports to be sent to both primary and secondary phone

numbers. Enter 1 if it is desired that all reports are sent to both primary and

secondary phone numbers. If dual reporting is desired and Ademco High

Speed format is to be used at all, it must be selected as both the primary

and secondary transmission formats. If used with Split Reporting option 1

(1*34), alarms go to both primary & secondary numbers, while all other

reports go to secondary only. If used with Split Reporting option 2,

open/close and test messages go to both lines, while all other reports go to

primary.

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 131 132

Comentários a estes Manuais

Sem comentários

ADEMCO 4140XMPT2 Manual do Utilizador Página 57

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO 4140XMPT2