ADEMCO 4140XMPT2 Manual do Utilizador descarregar pdf (Página 59)

– 59 –

Wireless Options

1*28 RF TX Low Battery Annun.

Enter 0 if audible beep and display annunciation upon RF transmitter low

battery condition is desired only in disarmed state. Enter 1 if audible beep

and display is desired in both armed and disarmed states. Must be 1 for UL.

1*29 RF TX Low Battery Report Enable

Enter 1 if a trouble message for RF transmitter low battery conditions is to

be sent to the central station. Enter 0 if no report for transmitter low battery

is desired. Note that a trouble message will be sent for a transmitter

supervision failure independent of this selection. Must be 1 for UL.

1*30 RF Rcvr Supervision Check-In Interval

Enter the check-in monitoring interval in 2-hour increments. Enter 02-15

times 2 hours (4-30 hours). Failure of a receiver to receive any RF signal

within the time entered will result in activation of the response type

programmed for zone 90 for the first receiver and zone 88 for the second

receiver and their related communication reports. Enter 00 to disable

receiver supervision. Max. "6" (12 hr) for UL.

1*31 RF Transmitter Check-In Interval

Enter the check-in monitoring interval in 2-hour increments; enter 02-15

times 2 hours (4-30 hours). Failure of an individual transmitter to send a

supervision signal within the time entered will result in a trouble response

and related communication report. Entry 00 disables transmitter

supervision. Max. "6" (12 hr) for UL.

1*32 Receiver Type

Enter 0 if using 4280 series Receivers. Enter 1 if using 4281 series

receivers. enter 2 if using 5881 series receivers. Important: the 4281

microprocessor must have part number N5334Vx, where x is any number.

1*44 Wireless Keypad Tamper Detect

Enter 1 to enable tamper detection on wireless keypad. Enter 0 if tamper

detection is not desired. If this feature is enabled, any attempt to tamper by

means of many trial entries at a wireless keypad will be blocked by the

control panel. If more than 40 key depressions are received without a valid

sequence (arm, disarm, etc.), the Control panel will disable the wireless

keypad. The inhibit is removed once a valid key sequence is received from

a wired keypad.

1*48 Wireless Keypad Assignment

Enter the partition in which the RF keypad is used, 1-8. Enter 0 if no RF

keypad is used.

1*49 Disable Trouble Sounder For RF Supervision

Enter 1 to disable trouble sounding for transmitter check-in failure. Enter 0

if audible trouble sounding is desired. Must be "0" for UL.

1*57 Enable 5800 RF Button Global Arm

Enter 1 to have the system arm/disarm in accordance with the button's

user's global arming settings. Enter 0 if the button is not to be used to

global arm the system (however, home partition arming will still occur).

1*58 Enable 5800 RF Button Force Bypass

Enter 1 to allow the RF Button user to force bypass all faulted zones.

When attempting to arm the system, the console will beep once after

pressing the button, if any faulted zones are present. If this feature is

enabled, the user should then press the button again within 4 seconds to

force bypass those zones and arm the system.

Partitioning Options 2*17 Number Of User Codes Per Partition

Enter 01-99 for each partition used in the system. Enter 01 for unused

partitions. Total number of user codes in the system must be less than or

equal to 128. Note that one user number is automatically assigned to each

partition, regardless of whether that partition has been enabled.

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 131 132

Comentários a estes Manuais

Sem comentários

ADEMCO 4140XMPT2 Manual do Utilizador Página 59

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO 4140XMPT2