ADEMCO Security System VISTA-15CN Guia de Configuração Página 105
- Página / 132
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
22–1
SECTION 22
System Operation
••••••••••••••••••••••••••••••••••••••••••••••••••
In This Section
♦
Security Codes
♦
Keypad Functions
♦
Relay/Powerline Carrier Devices
♦
4285/4286 VIP Module
♦
Exit Error Alarm Displays
♦
Trouble Conditions
♦
Setting the Real-Time Clock
••••••••••••••••••••••••••••••••••••••••••••••••••
Security Codes
Installer Code
The installer programs the 4-digit Installer code initially as part of the programming
procedure. The factory default Installer code is 4-1-1-2, but may be changed in field
✱
20.
The Installer code is the only code that can enter Programming mode. In Normal Operation
mode, it is also used to enter the Master code, which allows access to the normal functions of
the system.
Master Code
In Normal Operation mode,
the Installer code is used to enter the 4-digit Master security
code using
the hardwired connected keypad.
Therefore:
To enter the system's Master code, enter:
[Installer code] + [8] + [0] + [2] + [desired 4-digit Master code]
To change the Master code, enter:
[Master code] + [8] + [0] + [2] + [new Master code] + [new Master code again]
Secondary User Codes
In Normal Operation mode, the Master security code can be used to assign up to 14
Secondary 4-digit security codes, including a Temporary code and a Duress code. The Master
code is also used to remove any Secondary User code(s) from the system (individually).
To assign (or change) a Secondary security code, enter the following on the keypad:
[Master code] + [8] +
User
No.
[(03–16)] + [Secondary User Code]
The system emits a single beep when each secondary code has been successfully entered.
To
delete
a Secondary security code,
enter the following on the keypad
:
[Master code] + [8] +
User No.
[(03–16)]
Temporary User Code:
This user code can only be assigned to User 15 (
[Master code] +
[8] + [1] + [5] + [4-digit Temporary code]
)
on a strictly temporary basis because
whenever
a 4-digit Master code is keyed into the keypad, the existing Temporary code is
removed.
NOTES:
•
All Master and Secondary User security codes permit access to the system for arming,
disarming, etc.
• The Installer code can disarm the system only if it was used to arm it.
• Temporary code (User 15) behaves as Secondary User codes 3 through 14, except that a
keypad entry of a Master code permanently disallows use of this code, and if this code was
not used to arm the system, it cannot be used to disarm the system.
• Duress code is User code No. 16. When this is used to perform any system operation, a
special code is sent to the monitoring station. Instruct users to be careful not to use this
code for normal usage.
- 9,67$ 1
- 9,67$&1 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- Installing the Control 13
- V15-01-V0 14
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Section 12: Final Power-Up 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–6 23
- 2000 OHMS 24
- Programming Hardwired Zones 26
- Wired Zone Expansion 27
- DISARMED 29
- READY TO ARM 29
- Wireless Expansion 31
- < < 32
- Installing the 5800TM Module 33
- Jam Detection and Reporting 33
- Appendix A 36
- 1 2 3 4 5 37
- Powerline Carrier Devices 41
- Programming Relay Outputs 42
- 4285 & 4286 VIP Module 43
- Section 11: 44
- Audio Alarm 44
- Verification (AAV) Unit 44
- 4285 or 4286 45
- VIP MODULE 45
- External Sounders 47
- Sounder Connections and Power 48
- Sounder Supervision 48
- Testing the Sounder 48
- Long Range Radio 49
- Dynamic Signaling Feature 50
- 1 2 3 4 5 6 52
- Final Power-Up 53
- Battery Tests 54
- Mechanics of Programming 55
- Loading Factory Defaults 57
- Exiting the Programming Mode 57
- Section 18. Zone Lists 61
- Data Field Descriptions 63
- ZONE SOUNDS & 65
- TIMING ( 65
- Interactive 69
- Zone Programming 77
- 79
- To Remove a Zone 82
- Section 16 - Zone Programming 85
- Output Device Programming 87
- Zone Lists 93
- Cross Zoning - Zone List 04 94
- NIGHT-STAY - Zone List 05 94
- Alpha Descriptor Programming 95
- Summary Mode Display 96
- ALPHA VOCABULARY LIST 98
- CHARACTER (ASCII) CHART 98
- Remote Programming and 99
- Control (Downloading) 99
- Initial Download 100
- Remote Programming Commands 100
- System Communication 101
- FORMAT TYPE DESCRIPTION 102
- System Operation 105
- Keypad Functions 106
- Setting the Real-Time Clock 110
- Testing the System 111
- Troubleshooting Guide 113
- SMOKE DETECTOR 114
- CONTACTING TECHNICAL SUPPORT 115
- In This Section 117
- APPENDIX A 121
- Regulatory Agency Statements 123
- Warnings and Limitations 125
- VISTA-15/VISTA-15CN 131
- SUMMARY OF CONNECTIONS 131
- Copyright 132
- 2000 PITTWAY CORPORATION 132
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO Security System VISTA-15CN
(20 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.129 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais