ADEMCO Security System VISTA-15CN Guia de Configuração descarregar pdf (Página 106)

VISTA-15/VISTA-15CN Installation and Setup Guide

22–2

• If a Secondary User code is inadvertently repeated for different users, the lower user

number takes priority.

• Opening and Closing reports are sent for the Installer code as No. 01, with the appropriate

subscriber number. Each Master code and set of Secondary User codes are sent as Nos. 02

and 03–16, respectively, in Contact ID format (with the appropriate subscriber number); in

4+2 format, codes are sent as 1–F, “F” for anything greater than 14.

Keypad Functions

The keypad allows the user to arm and disarm the system, and to perform other system

functions, such as bypass zones and display zone descriptors. Zone and system conditions

(alarm, trouble, bypass) are displayed in the display window.

All keypads with backlighting capability automatically illuminate when system is placed in

entry mode (when any data entry key is pressed).

Arming Commands

The following is a brief list of system commands. For detailed information concerning system

functions, refer to the User Guide.

Disarmed, Not Ready Before arming, the system must be in the Ready condition (all

zones must be intact). If the NOT READY message appears,

press [

✱

] (READY

key) to display faulted zones.

Arming AWAY Enter code + [2] (AWAY), or [#] + [2]

†

, or depress the [A] key for

2 seconds

†

Arming NIGHT-STAY ......Enter code + [3] (STAY) + [3] (STAY), or [#] + [3] + [3]

†

, or

depress [C] for 2 seconds, which

arms the interior zones (Interior

Follower and/or Interior with Delay) programmed in Zone List

05. All other interior zones are automatically bypassed. The

installer determines which zones are to be included in this list.

Arming STAY Enter code + [3] (STAY), or [#] + [3]

†

, or depress the [B] key for 2

seconds.

Arming INSTANT Enter code + [7] (INSTANT

) or [#] + [7]

†

Arming MAXIMUM...........Enter code + [4] (MAXIMUM)

or [#] + [4]

†

Disarming Enter code + [1] (OFF).

Bypassing Zones Enter code + [6] (BYPASS) + zone number(s).

Forced (Quick) Bypass....(If enabled) To automatically bypass all faulted zones, use the

Quick Bypass method: Enter code + [6] (BYPASS), then wait for

all open zones to be displayed. Arm the system when display

indicates BYPASS and READY TO ARM.

Chime Mode

.......................

Enter

code + [9] (CHIME).

To turn chime off, enter code + [9] (CHIME) again.

†

If Quick Arm (field

✱21) is enabled.

The arming state of the system can be changed at any time by entering the 4-digit user code

plus the number key (2, 3, 4, or 7) that represents the arming state desired. It is not

necessary to disarm the system in order to make the desired change.

Quick Arming

If you enabled Quick Arm for the system (field

✱

21):

• With the system in the disarmed state you can press the [#] key instead of entering the

security code to perform any of the arming procedures (STAY, NIGHT-STAY, INSTANT,

AWAY, or MAXIMUM).

• The [A], [B], and [C] keys provide single-button arming capability. However, the arming

state can only be increased when using these lettered keys as follows: if you armed the

system using the [B] (STAY) key, you can increase the arming level by pressing the [C]

(NIGHT-STAY) key or [A] (AWAY) key.

1 2 ... 101 102 103 104 105 106 107 108 109 110 111 ... 131 132

Comentários a estes Manuais

Sem comentários

ADEMCO Security System VISTA-15CN Guia de Configuração Página 106

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso ADEMCO Security System VISTA-15CN