66
SYSTEM COMbWNICATZONS
CONTACT ID
REPORTING
Contact ID Reporting provides faster transmission speed and very specific
event code reporting, resulting in faster, more confident alarm decision
making by the central station, when compared to the other reporting formats
available (Ademco Low Speed, Sescoa. Radionics, etc.). This is the only
format that can identify all 64 protection zones by their unique zone (Contact)
ID numbers, and provides a l-digit event qualifier and 3digit. specifically
defined event code.which quickly identifies the condition being reported.
This format is supported by Ademw 685 Digital Receivers operating with
Rev. 4.4, or higher, software (Rev. 4.4 can only be supported in 685 Digital
Receivers equipped with the 68548 expanded memory card).
Contact ID reports in DTMF (Dual Tone Multi-Frequency @ 10 characters per
second) and responds to a 1400 Hz followed by 2300 Hz handshake, and a
1400 Hz kissoff. This format also uses checksum instead of two message
verification. A complete report takes under 3 seconds.
To enable contact ID reporting, enter a “1’ in field 1’32. To choose which
zones are to be reported enter random, non-zero values (01-l 5) in fields ‘61-
‘&t for zones 1 through 27, fields ‘65-‘68 for non-alarm reports and fields
1’35 - 1’39 for zones 28 through 64, and fields 1’42 and 1’43 to enable RF
Supervisory zones 88, 89. 90 8 91. (Note: A -Odl in any of these fields will
eliminate the report!). DO NOT enter the same value for all zones, as this will
affect how quickly swinger supression will disable communication.
ADVISORY
,-.
Ademco’s new Contact ID reportlng Is capable of uniquely
reportlng all 64 zones of Information, as well as openings and
closings for all 22 users, to central stations equipped wlth the
Ademco 685 receiver uslng software level 4.4 or higher. 685
software levels below 4.4 cannot support Contact ID reporting.
For Information regardlng updatlng the 685 receiver, contact
Ademco’s Technlcal Support group at 1-800-645-7492.
-. :-
.--..
TABLE 4. CONTACT ID REPORTING CODE DEFINITIONS
Contact ID Reporting takes the following format: CCCC 0 EEE GG 222 where:
cccc -
Customer (subscriber) number.
Q
P Event qualifier, where: Emnew event (1) and R= restore (3)
EEE
= Event code (3 hexadecimal digits), defined in the table below.
$zg f
Atways 00.
Zone/contact ID number reporting the alarm (001-099) or user
number (001-022) for open/close reports. System status
messages (AC Loss, Walk Test, etc.) contain zeroes in the SSS
bcation.
EVENT CODES:
Code DNJUI.D~
Code Deflnltlon
110
FmAbnn
342
Trouble-Poll Loop Short
121
343
Trouble&p. Mod. Trble
122
Silent Panic
380
Trouble
12.3
Audible
Panic
381
Loss of Supervision - RF
131
Perimeter Burglary
383
Sensor Tamper
132
Interior Burglary
304
RF Transmitter Low Battery
133
24 Hour Burglary
401 OC By User
134
Entry/Exit Burglary
403
Power-Up Armed
135
DaylNiht Burglary
406
cancel
142
Poking Loop Short Alarm
407
Remote Ann (Downbad)
143
4162LMB Module Failure
408
Quidc Arm
150
301
244Hou~Auxiliary
409
Keyswitch OIC
411
Call back Requested
302
Low System Battery
570
Bypass
305
System Reset
601
Manually Triigered Test
z
Program Tamper
602
Periodic Test
Battery Test Fail
--
.-..
ADEMCO’s VISTA
XM
SERIES TECHNICAL REFERENCE MANUAL
WWW.DIYALARMFORUM.COM
(8 páginas)
(173 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais